Connection GlobalSat GPS trackers

In this review we will answer the questions about the connection of GPS trackers GlobalSat to the GISFile service.

I use one of devices which are considered below. So I can describe in detail the settings process.

SIM-card preparation

Before the connecting of GPS tracker please prepare the SIM card. I recommend you to disable the PIN-code request and the receiving of advertising messages. Will not forgot to check the availability of money on your card balance. If the possibility of using GPRS services is disable, send the request to activate the services GPRS GSM to operator USSD (for example, at MTS is a free USSD request *109*212# - for Ukraine).

Car GPS tracker GlobalSat TR-600

The preparation to the work

Disconnect the device.

Open the rubber plug of the SIM-card connector on the housing the tracker. Set SIM-card into the slot as it is shown in the photo. Metallic contacts should look up and the beveled angle of SIM-card should be ahead. To extract the SIM-card lightly press it and she «jump out» from the slot.

Connect the interface cable RS-232 to the PC serial port and to the interface port tracker.

Connect the GSM antennas and GPS to the tracker.

Connect the black wire (common) with the minus of constant current source the voltage 12 ~ 24 Volt.

Connect the red (power) and yellow (ACC) wires to the plus of the same source. The tracker will begin his work.

The configuring of GPS tracker

Download and run the program "TR-600 Config Tool.exe".

In the field "COM" select the COM-port number which the tracker is connected to(usually - COM1) or click on the button "Scan". Then click the "Start" – the communication with tracker is installed.

Presently you can:

- load the settings from the tracker into the program: Load from device
- save the settings from the program into a file: Save to file
- load the settings from the file into the program: Load from file
- save the program settings in the tracker: Save to device

Download the parameters for connecting GPS tracker to the service GISFile

Pay your attention!The filling of GPRS parameter ANP depends on mobile operator (Example: MTC - internet, Kyivstar - wap.kyivstar.net). If you have another operator you need to fill the User Name and Password. If you did not disabled the PIN-code request, you need to fill the PIN Code field. After the downloading of parameters fill the values Device ID, Phone Number of SIM Card, SMS Phone Number1.

Personal GPS-tracker GlobalSat TR-206

The preparation to the work

Disconnect the device.

Move the latch of battery cover to leftward.

Open the battery cover.

Insert the SIM-card. Metallic contacts should look down and the beveled angle of SIM-card should be back.

Insert the battery pack.

Close the battery cover.

Move the latch to the right to lock the cover.

The Configuring of GPS tracker

Download and install the driver "VCPDriver_V1.1_Setup.exe".

Connect the GPS-tracker to the computer via mini-USB cable.

Download and run the program "TR-206 Config Tool.exe".

After this actions you can:

- load the settings from of the GPS tracker into the program: Load from device
- save the settings of the program into the file: Save to file
- load the settings from the file into the program: Load from file
- save settings from the program into the tracker: Save to device

GlobalSat Config Tool

Download the parameters for connecting the GPS tracker to the service GISFile

Examples of messages

Transmission by GPRS (protocol IMEI):
GSr,354660042226111,00,4,c000,c000,3,180414,130630,E03215.7864,N4831.0579,99,0.00,0,7,1.3,12420,12390mV,0,0,0,0,0,5222,0,255,01,8661,E92B*5F!
GSr,354660042226111,04,k,c000,c000,3,250612,133640,E03215.7806,N4831.0618,122,0.00,0,8,1.2,12690,12690mV,0,0,0,0,0,44179,0,255,01,8598,E92E*04!
GSr,354660042226111,00,4,c000,c000,3,250612,140624,E03215.7704,N4831.0597,136,0.00,0,7,1.2,12710,12710mV,0,0,0,0,0,44179,0,255,01,8598,E92E*5A!